Shopping

Featured Items
Hypermax High Strength Connecting Rod

Hypermax Ultimax Super Strength Forged High Alloy Connecting Rods with high strength ARP bolts
Racers Special Discount for a limited time only. In stock to ship today, no 6 week lead time.

Retail Price: $3,620.00

Our Price: $3,250.00

Hypermax Ultimax Super Strength Forged High Alloy Connecting Rods
A set of 8 forged connecting rods with the center to center controlled within .002. Stronger than billet connecting rods and the powdered metal production rods currently being used. Lighter than stock rods up to 40 grams (When compared to factory powdered metal rods).
Refined grain 4340 aircraft quality forgings which are vacuum heat treated for optimum tensile and yield strength. Cryogenically treated to improve grain structure and shot peened for improved fatique life then magnafluxed for integrity.
ARP bolts.
Supports 2000 BHP on diesel fuel only.

Hypermax 6.0 L Bead Seal Head Gasket Set

2003-2008 Ford 6.0L Power Stroke Performance Wire Ring Bead Seal Head Gaskets. No machining required, capable of running 500 plus BHP.
Works With 18 mm & 20 mm dowel

Retail Price: $700.00

Our Price: $525.00

New and Improved Bead Seal Gasket Body with impregnated rubber seal. Eliminate blown head gaskets with this assembly and no machining needed. Works well with programmers or in-line modules. Keeps your truck from whistling like a tea kettle. If you run over 30 Psi of boost then these are what you need! We tested these at 500 BHP for 40 hours. Intermittent runs to 625 BHP
Works with both 18 mm & 20 mm dowels Gasket is supplied as 18 mm dowel. Just remove the 4 tabs for 20 mm dowel

Gasket bodies are made from steel sheet and covered in graphite composite material and a small rubber bead is applied around all areas with aircraft stainless combustion rings.
Applications: 2003-2008 Ford F-Series pickup, Van, and Excursion with 6.0L Power Stroke diesel.
Stud Update: We have tested these gaskets with ARP head studs and found no extra sealing performance gain over factory bolts and our gaskets. If used, ARP installation instructions must be followed.
Stacking of boxes will also fail the gasket. This means using an in-line programmer along with programming the factory PCM. This is due to the extreme timing advance that is produced by both modifications.
Warranty: There is no warranty with this product, if the kit fails it is due to installation error or operator error. If you have more than 500 BHP or stack boxes the gaskets will fail. We have hundreds of hours of testing and they do not fail when used in the manner which they are designed.
Includes 2 Bead Seal gasket bodies, 8 rings, and Do-it-yourself installation instructions.

Hypermax 6.0 L Competition Head Gasket Assembly

2003-2008 Ford 6.0L Power Stroke Competition Head Gaskets. Machining required, capable of running 1500 plus BHP.
Works With 18 mm & 20 mm dowel

Retail Price: $1,600.00

Our Price: $1,250.00

Are you running compound turbos and big injectors and keep blowing head gaskets? The Hypermax Competition head gaskets are designed for you. A special 3 ring system keeps cylinder pressure leakage from failing the gasket body. Machining is required. This gasket kit is reusable and will take in excess of 140 psi of boost.
Works with 18 mm & 20 mm dowels Gasket is supplied as 18 mm dowel. Just snap the 3 tabs off for 20 mm dowel.

Gasket bodies are made from steel sheet and covered in graphite composite material with 3 piece compbustion rings.
Applications: 2003-2008 Ford F-Series pickup, Van and Excursion with 6.0L Power Stroke diesel.
Includes 2 gasket bodies, 8 inner rings, 8 c-rings, 8 outer rings, gasket spray, and Do-it-yourself installation instructions.

Hypermax 6.4L Bead Seal Head Gasket Set

2008-2010 Ford 6.4L Power Stroke Performance Bead Seal Wire Ring Head Gaskets. No machining required, capable of running 500 plus BHP.

Retail Price: $700.00

Our Price: $525.00

New and Improved Bead Seal Gasket Body with impregnated rubber seal. Eliminate blown head gaskets with this assembly and no machining needed. Works well with programmers or in-line modules. Keeps your truck from whistling like a tea kettle. If you run over 30 Psi of boost then these are what you need! We tested these at 500 BHP for 40 hours. Intermittent runs to 625 BHP

Gasket bodies are made from steel sheet and covered in graphite composite material and a small rubber bead is applied around all areas with aircraft stainless combustion rings.
Applications: 2008-2010 Ford F-Series pickup with 6.4L Power Stroke diesel.
Stud Update: We have tested these gaskets with ARP head studs and found no extra sealing performance gain over factory bolts and our gaskets. If used, ARP installation instructions must be followed.
Stacking of boxes will also fail the gasket. This means using an in-line programmer along with programming the factory PCM. This is due to the extreme timing advance that is produced by both modifications.
Warranty: There is no warranty with this product, if the kit fails it is due to installation error or operator error. If you have more than 500 BHP or stack boxes the gaskets will fail. We have hundreds of hours of testing and they do not fail when used in the manner which they are designed.
Includes 2 Bead Seal gasket bodies, 8 rings, and Do-it-yourself installation instructions.

Hypermax 6.4 L Competition Head Gasket Assembly

2008-2010 Ford 6.4L Power Stroke Competition Head Gaskets. Machining required, capable of running 1500 plus BHP.

Retail Price: $1,600.00

Our Price: $1,250.00

Are you running compound turbos and big injectors and keep blowing head gaskets? The Hypermax Competition head gaskets are designed for you. A special 3 ring system keeps cylinder pressure leakage from failing the gasket body. Machining is required. This gasket kit is reusable and will take in excess of 140 psi of boost.
Gasket is supplied as 18 mm dowel. Just snap the 3 tabs off for 20 mm dowel.

Gasket bodies are made from steel sheet and covered in graphite composite material with 3 piece compbustion rings.
Applications: 2008-2010 Ford F-Series pickup with 6.4L Power Stroke diesel.
Includes 2 gasket bodies, 8 inner rings, 8 c-rings, 8 outer rings, gasket spray, and Do-it-yourself installation instructions.

7.3L Aluminum Powerstroke Valve Covers

Hypermax Premium Ultimax Aluminum Valve Covers

Retail Price: $925.00

Our Price: $750.00

Cast aluminum valve covers to replace those rusty old ones. These were designed for our inline pump application but due to requests we have made them to replace the factory steel pieces. These can be polished for that custom under the hood look. Utilizes the factory harware and valve cover harnesses.

7.3L CGI Powerstroke Crankcase

Hypermax Premium Ultimax CGI (Compacted Graphite Iron) 7.3L Powerstroke Crankcase.

Retail Price: $10,000.00

Our Price: $9,500.00

Hypermax Ultimax crankcases for Ford Powerstroke diesel engines are cast using CGI material for a 60% improvement in strength and reliability over the factory design. Built to withstand the extreme cylinder pressures of single or twin turbochargers and nitrous oxide injected systems.
Don’t waste time and money with a junkyard block on your high performance Powerstroke. The new powder coated CGI crankcase is fully machined and line bored to factory specifications.
Also available with unfinished cylinder and main bearing bores.

Powerstroke Engine Bedplate

7.3L Powerstroke Crankcase Engine Girdle Bedplate

Retail Price: $2,900.00

Our Price: $2,350.00

7.3L Powerstroke Crankcase Engine Girdle Bedplate, designed to strengthen the lower end of your powerstroke. This unique cast bedplate ties the main bearing caps to the engine oil pan rail. Prevents cap movement and fretting of the mating components. Similar to the 6.0L powerstroke bedplate design to tie the bottom end of the crankcase for the ultimax support.
Without this kind of added support the crankcase will fail in the bulkhead sections.
You will need to modify your oil pan to utilize this product. Comes complete with mounting hardware and instructions.

300/400 Series Front Cover

300 and 400 series aluminum front cover

(Call for Price)

Aluminum International Harvester 300/400 series engine front cover for 66 series tractors. Exact duplicate of production cover and 50 pounds lighter than the cast iron cover. This part is also available in cast iron.

Big Valve Cylinder Head 774 2.5

Big valve heavy wall casting cylinder head for prostock tractors with 4 7/8" bore engines

(Call for Price)

Big valve heavy wall casting cylinder head for prostock tractors with 4 7/8" bore engines.
Includes high temperature 2.5" intake titanium valves and 1.9" diameter inconel exhaust valves, rotators, double valve spring package, titanium retainers and locks. Ports are designed for maxumum flow with optium swirl for this bore size.
This casting has increased thickness in critical crack prone areas and drilled for port water injection.

Prostock Turbo

Hypermax Prostock Turbocharger 4.9" exhaust with 5" inducer. Fits all makes of trucks and tractors.

(Call for Price)

Hypermax Prostock Turbocharger 4.9" exhaust with 5" inducer. Billet compressor wheel wheel with inconel turbine wheel. Fits all makes of trucks and tractors Hypermax center section, turbine housing and compressor housing. Custom billet 5" inlet compressor wheel. Choices of turbine housing available, let us know upon ordering.

Hypermax Injection Pump IH

Hypermax Mod-S INline Injection Pump 15mm Plungers and high lift camshaft

(Call for Price)

Hypermax Mod-S inline Injection Pump 15mm Plungers and high lift camshaft.
Complete mounting adapter, drive gear and additional support brackets for 400 series International Engines Hypermax cast aluminum housing with 15mm plunger and barrel assemblies, high lift camshaft. All parts are Hypermax designed and built.

Hypermax Injection Pump John Deere

Hypermax Mod-S INline Injection Pump 15mm Plungers and high lift camshaft for John deere applications

(Call for Price)

Hypermax Mod-S inline Injection Pump 15mm Plungers and high lift camshaft. Hypermax cast aluminum housing with 15mm plunger and barrel assemblies, high lift camshaft. All parts are Hypermax designed and built.

4.625 Bore Cylinder set JD Billet

4.625 Bore Cylinder set for John Deere, 12:1 Compression Ratio with solid wrist pins and billet pistons

(Call for Price)

4.625 Bore Cylinder set 12:1 Compression Ratio with solid wrist pins and billet pistons.
This set includes billet pistons, rings, clips, solid wrist pins, cylinder sleeves and "O" rings.
Valve cut outs also included, let us know your valve size.
No block boring required
Note:You must also purchase the dynamic head gasket assembly to work with this kit due to the sleeve design.

Prostock Turbo John Deere

Hypermax Prostock Turbocharger 4.9" exhaust with 5" inducer. Fits all makes of trucks and tractors.

(Call for Price)

Hypermax Prostock Turbocharger 4.9" exhaust with 5" inducer. Billet compressor wheel wheel with inconel turbine wheel. Fits all makes of trucks and tractors Hypermax center section, turbine housing and compressor housing. Custom billet 5" inlet compressor wheel. Choices of turbine housing available, let us know upon ordering.

Prostock Exhaust Manifold

Prostock IH HI Flow Exhaust Manifold

(Call for Price)

Prostock IH HI Flow Exhaust Manifold
Cast 3 piece exhaust manifold complete with seals and mouting hardware.

Prostock Intake Manifold

Pro Stock cast Aluminum Intake Manifold

(Call for Price)


Prostock Cross Over Pipe

Prostock turbo to intake manifold cross over

(Call for Price)

Prostock turbo to intake manifold cross over to connect a Hypermax prostock turbo charger to the prostock intake manifold.
Must also have the Hypermax Prostock cast exhaust manifold.

4.625 Bore Cylinder set cast

4.625 Bore Cylinder set 12:1 Compression Ratio and cast pistons

(Call for Price)

4.625 Bore Cylinder set 12:1 Compression Ratio.
This set includes cast pistons, rings, clips, hollow pins, cylinder sleeves and "O" rings.
Valve cut outs also included, let us know your valve size.
Solid piston pins also available for an additional $385
Note:You must also purchase the dynamic head gasket assembly to work with this kit due to the sleeve design.

4.625 Bore Cylinder set JD Billet

4.625 Bore Cylinder set for John Deere, 12:1 Compression Ratio with solid wrist pins and billet pistons

(Call for Price)

4.625 Bore Cylinder set 12:1 Compression Ratio with solid wrist pins and billet pistons.
This set includes billet pistons, rings, clips, solid wrist pins, cylinder sleeves and "O" rings.
Valve cut outs also included, let us know your valve size.
No block boring required
Note:You must also purchase the dynamic head gasket assembly to work with this kit due to the sleeve design.

4.625 Bore Cylinder set cast

4.625 Bore Cylinder set 12:1 Compression Ratio with solid wrist pins and cast pistons

(Call for Price)

4.625 Bore Cylinder set 12:1 Compression Ratio.
This set includes cast pistons, rings, clips, solid wrist pins, cylinder sleeves and "O" rings.
Valve cut outs also included, let us know your valve size.
Note:You must also purchase the dynamic head gasket assembly to work with this kit due to the sleeve design.

4.625 Bore Cylinder set cast

4.625 Bore Cylinder set 13:1 Compression Ratio and cast pistons

(Call for Price)

4.625 Bore Cylinder set 13:1 Compression Ratio.
This set includes cast pistons, rings, clips, hollow wrist pins, cylinder sleeves and "O" rings.
Valve cut outs also included, let us know your valve size.
Solid piston pins also available for an additional $385
Note:You must also purchase the dynamic head gasket assembly to work with this kit due to the sleeve design.

4.625 Bore Cylinder set cast

4.625 Bore Cylinder set 13:1 Compression Ratio with solid wrist pins and cast pistons

(Call for Price)

4.625 Bore Cylinder set 13:1 Compression Ratio.
This set includes cast pistons, rings, clips, solid wrist pins, cylinder sleeves and "O" rings.
Valve cut outs also included, let us know your valve size.
Note:You must also purchase the dynamic head gasket assembly to work with this kit due to the sleeve design.

4.875 Bore Cylinder set

4.875 Bore Cylinder set 12:1 Compression Ratio for deckplace applications

(Call for Price)

4.875 Bore Cylinder set 12:1 Compression Ratio.
This set includes billet pistons, rings, clips, solid wrist pins, cylinder sleeves and "O" rings.
Valve cut outs also included, let us know your valve size.
Note:You must also purchase the dynamic head gasket assembly to work with this kit due to the sleeve design.

4.875 Bore Cylinder set

4.875 Bore Cylinder set 12:1 Compression Ratio for non deckplace applications

(Call for Price)

4.875 Bore Cylinder set 12:1 Compression Ratio.
This set includes billet pistons, rings, clips, solid wrist pins, cylinder sleeves and "O" rings.
Valve cut outs also included, let us know your valve size.
Note:You must also purchase the dynamic head gasket assembly to work with this kit due to the sleeve design.

4.875 Bore Cylinder set

4.875 Bore Cylinder set 13:1 Compression Ratio for deckplace applications

(Call for Price)

4.875 Bore Cylinder set 13:1 Compression Ratio.
This set includes billet pistons, rings, clips, solid wrist pins, cylinder sleeves and "O" rings.
Valve cut outs also included, let us know your valve size.
Note:You must also purchase the dynamic head gasket assembly to work with this kit due to the sleeve design.

4.875 Bore Cylinder set

4.875 Bore Cylinder set 13:1 Compression Ratio for non deckplace applications

(Call for Price)

4.875 Bore Cylinder set 13:1 Compression Ratio.
This set includes billet pistons, rings, clips, solid wrist pins, cylinder sleeves and "O" rings.
Valve cut outs also included, let us know your valve size.
Note:You must also purchase the dynamic head gasket assembly to work with this kit due to the sleeve design.

4.3 Bore Cylinder set cast

4.3 Bore Cylinder set 12:1 Compression Ratio with cast pistons

(Call for Price)

4.3 Bore Cylinder set 12:1 Compression Ratio.
This set includes cast pistons, rings, clips, hollow pins, cylinder sleeves and "O" rings.
Valve cut outs also included, let us know your valve size.
Solid piston pins also available for an additional $385
Note:You must also purchase the dynamic head gasket assembly to work with this kit due to the sleeve design.

4.3 Bore Cylinder set Cast

4.3 Bore Cylinder set 12:1 Compression Ratio with solid wrist pins and cast pistons

(Call for Price)

4.3 Bore Cylinder set 12:1 Compression Ratio.
This set includes cast pistons, rings, clips, solid wrist pins, cylinder sleeves and "O" rings.
Valve cut outs also included, let us know your valve size.
Note:You must also purchase the dynamic head gasket assembly to work with this kit due to the sleeve design.

4.3 Bore Cylinder set cast

4.3 Bore Cylinder set 13:1 Compression Ratio with cast piston

(Call for Price)

4.3 Bore Cylinder set 13:1 Compression Ratio.
This set includes cast pistons, rings, clips, hollow wrist pins, cylinder sleeves and "O" rings.
Valve cut outs also included, let us know your valve size.
Solid piston pins also available for an additional $385
Note:You must also purchase the dynamic head gasket assembly to work with this kit due to the sleeve design.

4.3 Bore Cylinder set cast

4.3 Bore Cylinder set 13:1 Compression Ratio with solid wrist pins and cast piston

(Call for Price)

4.3 Bore Cylinder set 13:1 Compression Ratio.
This set includes cast pistons, rings, clips, solid wrist pins, cylinder sleeves and "O" rings.
Valve cut outs also included, let us know your valve size.
Note:You must also purchase the dynamic head gasket assembly to work with this kit due to the sleeve design.

IH Roller Rocker Arms

IH 400 Series Roller Rocker Arms

(Call for Price)

IH 400 Series Roller Rocker Arms. High alloy investment cast steel rocker arms. Incredible stifness results in higher effective valve lift. Far superior than billet aluminum machined rockers
Supplied with roller tip and replaceable bronze bushing and adjusting screw assembly.
Guaranteed for life against breakage

400 Series Valve Cover

400 Series Cast Aluminum Valve Cover

(Call for Price)

400 Series Cast Aluminum Valve Cover with mounting hardware and O-Ring.
Designed to replace the factory steel stamped valve cover and clear aftermarket rocker arms. O-ring seal between cover and cylinder head. Extra support around mounting points to prevent valve cover blow out when you burn a piston and make lots of crankcase pressure.
 
EZeCom Powered by MAP eCommerce
© 2022 Hypermax. All Rights Reserved